CAT CLASS: HQ-10841

26-32 ft Extension Ladder

The 26-32 ft extension ladder is specified for three-storey access, tall commercial facades, steep roof pitches, and chimney work where a 20-26 ft extension ladder falls short. This size class bridges mid-height residential work and the longest extension ladders in the fleet. Maximum extended heights in this range typically reach 27–31 ft, with load capacities from 225 to 375 kg depending on duty rating.

288

Modèles

Marques

Cat classes

Choisissez une classe de taille — la capacité et la portée varient selon la gamme.

Spécifications clés

Spécification	Plage typique	Signification
Max height	27–31 ft (8.2–9.4 m)	Extended length determines the highest safe working position, accounting for required overlap and setup angle.
Load capacity	496–827 lb (225–375 kg)	Duty rating varies from Type II (commercial) to Type IA (heavy-duty industrial); higher ratings accommodate tools and materials.
Retracted length	~14–17 ft	Nested length governs transport vehicle requirements and jobsite maneuverability.
Weight	~30–45 kg	Heavier-duty ratings and fiberglass construction increase mass; two-person handling is standard for this size.

Comment choisir

This size is appropriate when the work height exceeds the reach of a 20-26 ft extension ladder—typically three-storey eaves, commercial storefronts, or chimney stacks on steep-pitch roofs. If the task involves standard two-storey residential siding, soffit, or gutter work below 24 ft, the 20-26 ft extension ladder offers easier handling and setup. For work above 30 ft, such as four-storey buildings or large commercial facades, the 32+ ft extension ladder provides the necessary reach. Setup angle, overlap requirements, and the distance of the base from the wall all reduce effective working height, so the actual task elevation should be several feet below the ladder's maximum extended length.

Ce que cette taille peut gérer

Three-storey residential exterior painting and window access
Tall commercial building facade maintenance and signage installation
Chimney inspection and repair on steep-pitch roofs
Electrical service mast work at 25–28 ft height
High soffit and fascia repair on split-level or hillside structures
Tree pruning and trimming at crown heights of 22–26 ft

Sécurité et opération

Setup angle of 75° (1:4 ratio—base one foot out for every four feet of height) is critical for stability; over-steepening or over-flattening increases tip or slide risk.
Minimum overlap between fly and base sections increases with extension length; consult manufacturer rung labels for required overlap at working height.
Two-person setup is standard practice due to weight and length; raising the fly section and stabilizing the base require coordination.
Tie-off or standoff stabilizers are often used at this height to prevent lateral movement and keep the ladder clear of fragile surfaces like gutters or siding.

Transport et logistique

Requires full-size pickup truck or flatbed trailer; retracted length of 14–17 ft typically overhangs compact truck beds.
Two-person lift recommended for loading and unloading due to 30–45 kg weight and length.
Roof racks or ladder racks on larger vans can accommodate this size with proper tie-down.

Alimentation

No power or fuel required; extension ladders are unpowered access equipment.
Fiberglass models are non-conductive and specified for electrical work; aluminum models conduct electricity and require clearance from live lines.

Questions fréquentes

What is the actual working height for a 28 ft extension ladder?

Working height is typically 3–5 ft less than maximum extended length due to required setup angle, rung overlap, and the fact that standing on the top rungs is unsafe. A 28 ft ladder generally provides safe working access to approximately 23–25 ft.

Can one person set up a ladder in this size range?

Solo setup is difficult and hazardous due to the 30–45 kg weight and 14–17 ft retracted length. Industry practice calls for two people to walk up the ladder from a horizontal position or to stabilize the base while extending the fly section.

What is the difference between Type I, Type II, and Type IA ratings in this size class?

Type II ladders support 225 kg (light commercial), Type I supports 250 kg (industrial), and Type IA supports 300+ kg (heavy-duty industrial). Higher ratings use thicker side rails and rungs, adding weight but increasing capacity for tools and materials on the ladder.

Comparer les modèles populaires

Chercher par spécification →

Normalisé aux mêmes unités. Un tiret signifie que la valeur n'a pas été publiée.

Modèle	Hauteur max	Capacité de charge
Louisville Ladder AE1232HD	29 ft (8.8 m)	827 lb (375 kg)
Louisville Ladder AE2232	29 ft (8.8 m)	661 lb (300 kg)
Louisville Ladder AE3232	29 ft (8.8 m)	551 lb (250 kg)
Louisville Ladder AE4232PG	29 ft (8.8 m)	496 lb (225 kg)
Louisville Ladder AE4240	30.8 ft (9.4 m)	496 lb (225 kg)
Louisville Ladder DXL3020-36PT	27.6 ft (8.4 m)	661 lb (300 kg)